realitystill.blogg.se - External usb audio interface audacity

External usb audio interface audacity manuals#
External usb audio interface audacity software#
External usb audio interface audacity mac#
External usb audio interface audacity windows#

You can always boost the level later with Effect > Amplify.

Try to aim for a maximum peak of around \xe2\x80\x936 dB, which corresponds to around 0.5 on the waveform.

Then right-click over USB Audio Codec, choose "Properties" and click the Levels tab. On Windows, right-click over the speaker icon > "Recording Devices".

External usb audio interface audacity windows#

If it does not, try adjusting the output level on the turntable (often, there is a gain control under the chassis).Īlternatively, you may be able to adjust the input level on Windows and Linux only, usually by looking for the speaker icon by the system clock.

The right-hand recording volume slider (by the microphone icon) can often be used to vary the loudness of the recording, but it may not function with all turntables.

In Mixer Toolbar, turn up the left-hand playback volume slider (by the speaker icon).

Turn monitoring on by clicking once on the microphone icon in the Recording Meter.

It also lets you hear the turntable without recording if you turn on monitoring (see the next section below).Įnable monitoring to set the recording level

External usb audio interface audacity software#

Software Playthrough lets you hear the turntable through the computer speakers when recording. This setting can also be enabled or disabled in Recording Preferences. Use Transport > Transport Options > Software Playthrough (on/off) and click "Software Playthrough" to turn it "on" (the checkmark is shown when it is "on"). Some higher-end USB recording interfaces may appear as their explicit manufacturer's name. Windows calls most USB external devices "microphones". These settings can also be changed in Devices Preferences.The Playback Device is set to the named speakers of the built-in computer sound device.The Recording Device is set to the USB device (in this case the device name, but often called or including the phrase "USB Audio CODEC").Use Device Toolbar to set the recording and playback devices and to set the recording channels to "2 (Stereo) Recording Channels", as in the below example on Windows 10: Set the Audacity Project Rate in Selection Toolbar at the bottom left of the Audacity screen to 44,100 Hz: If Audacity was already running when you connected the cable, restart Audacity or choose Transport > Rescan Audio Devices.

External usb audio interface audacity mac#

Set the Format to "44,100.0 Hz" and "2ch-16bit".įor a more detailed walk-through of the above steps for Mac, see Mac and USB input devices on the Audacity Wiki.

Select your USB input device in the list in the left pane of the Audio Devices window.

If the Audio Devices window is not visible, select Window > Show Audio Devices.From the Finder, select Go > Utilities and open Audio MIDI Setup.If the recording meter in the Sound preferences panel does not show input:.Select "USB Audio CODEC" or similar as the input device and verify the Recording Meter shows input.From Apple Menu > System Preferences select "Sound" and click on the Input tab.On the Advanced tab, in the "Default Format" section, make sure the dropdown menu is set to "2 channel 16-bit 44,100 Hz".įor a more detailed walk-through of the above steps for Windows (or if that does not work for your version of Windows), see Windows: accessing the Windows Sound controls.Click the Advanced tab set your required bit rate and sample rate from the Default Format dropdown (normally "2 channel 16-bit 44,100 Hz"). By the system clock, right-click over the Speaker icon select Sounds then the Recording tab, and then click on the USB device in the list and click Properties.System settings needed for Windows and Mac

If you want to select Start Monitoring, you need to have the Recording Meter enabled (note: NOT the Mixer Toolbar that some guides state). Monitoring the input is optional and allows you to hear the device through the computer speakers just like an ordinary turntable, or cassette deck, whenever it is playing, without having to record.

External usb audio interface audacity manuals#

You do not need to select Start Monitoring each time you launch Audacity, as some manuals urge you to.

Preferences are under the Edit menu (or under the Audacity menu on Mac).

Audacity Preferences are not under the File menu, as many manuals state.

This is not the case, rather you should be setting the USB device as your input.

Many manuals state that you should "select stereo mix for your input".

Here are some errors that you may come across: Sometimes the guides supplied with the devices are out-of-date or have errors.

The guides provided with the devices might be confusing, they are written by the device manufacturer rather than by Audacity.